SAFETY

1-COMPETITORS ARE RESPOSIBLE FOR THE PROPER USAGE AND INSTALLATION OF ALL SAFETY EQUIPMENT.

2-DRIVERS MUST WEAR APPROVED FIRE-RESISTANT SUITS, GLOVES, SHOES AND FULL FACE HELMENTS AT ALL TIME ON TRACK.

3-HELMENTS MUST BE FULL FACED AND MEET SA SNELL 2010 OR SFI.

4-THE USE OF A 5,6- OR 7-POINT RESTRAINT SYSTEM IS MANDATORY.

5-BELTS MUST BE CERTIFIED TO SFI SPEC 16.1 THESE RESTAINTS MUST BE WITHIN 2 YEARYS FROM THE DATE OF MANUFACTURE.

6-IT IS REQUIRED TO HAVE A FULLY FUNCTIONING FIRE EXTINGUISHER MOUNTED SECURELY INSIDE THE CAR AT ALL TIME.

7-ALL ALUMINUM SEATS MUST BE MOUNTED PRPERLY AND SECURLEY PER THE DIRECTIONS OR RECOMMENDATIONS FROM THE SEAT MANUFATURER. THE USE OF GRADE 5 OR BETTER HARDWARE IS ALSO REQUIRED TO ATTACH TO THE SEAT TO THE CHASSIS WITH MINIMUM 4 MOUNTING BOLTS (3/8 OR BIGGER). SEAT MOUNTING BRACKETS MUST USE PROPERLY SIZED BOLTS 3/8 INCH OR BIGGER WITH WASHERS TO MATCH THE HOLES IN THE MOUNTING BRACKET. NO OVERSIZED HOLES OR SLOTTED HOLES IN THE BRACKET.

INTERIOR

1-FACTORY DASH AND GAUGE CLUSTER MUST REMAIN STOCK AND MOUNTED IN STOCK LOCATION.

2-DASH PAD MUST BE REMOVED

3-ALUMINUM DASH IS PERMITTED BUT MUST BE ANY DEEPER THAN 14 INCHES.

4-MAY RUN AFTERMARKET GAUGES BUT THE FACTORY CLUSTER MUST BE REMAIN IN THE VEHICLE AND OPERATIONAL.

5-STEERING COLUMN MUST REMAIN STOCK AND MOUNTED IN STOCK LOCATION.

6-QUICK RELEASE STEERING COUPLER MAY BE USED BUT NOT MOUNTED TO STOCK COLOUM.

7-THROTTLE AND BRAKE PEDELS MUST REMAIN STOCK AND IN STOCK LOCATION WITH FACTORY HARDWARE.

8-ALL AIR BAGS MUST BE REMOVED FROM VEHICLE.

9-INTERIOR DECKING OF ANY KIND IS NOT ALLOWED

10-4 VERTICAL STEEL RODS MUST BE INSTALLED SECURLEY IN FRONT OF THE DRIVER.

11-ONLY 1 12VOLT MAX BATTERY MAY BE USED.

12-BATTERY MAY BE MOVED TO TRUNCK AREA OR BEHIND SEAT BUT MUDT BE MOUNTED SECURLEY.

​

BODY

1-MINIMUM 6-INCH-TALL NUMBERS MUST BE DISPLAYED ON THE FRONT NOSE.

2-MINIMUM 18-INCH-TALL NUMBERS MUST BE DISPLYED AND LEGIBLE ON BOTH SIDES AND ROOF OF CAR.

3-ALL FACTORY MOUNTINGLOCATIONS MUST REMAIN IN ORIGINAL LOCATION AND DESIGN.

4-ALL FLAMMABLE MATERIAL INCLUDING, BUT NOT LIMITED TO, GLASS AND PLASTIC MUST BE REMOVED FROM VEHICLE.

5-NO ADDITIOANL BODY COMPONETS ARE ALLOWED TO BE ATTACHED TO ANY PART OF THE VEHICLE TO ENHANCE THE AERODYNAMIC PROPERTIES OF THE CAR.

6-NO REAR SPOILERS OR WINGS ATTACHED TO ANY PART OF THE CAR.

7-NO SIDE SKIRTS INSTALLED ANYWHERE ON THE CAR.

8-MATERIAL IS NOT TO BE REMOVED FROM ANY PART OFM THE BODY OR FRAME FOR LIGHTING, CLEARANCE OR OTHERWISE EXCEPT FOR THE DRIVER & PASSENGER DOORS AND B PILLERS FOR ROLLBAR CLEARANCE.

9-ALL STOCK BOLTS ON BODY COMPONENTS MUST BE INSTALLED ON THE CAR INCLUDING DOORS, HOOD AND TRUNK.

10-HOOD AND TRUNK MAY UTILIZE FACTORY HINGES BUT MUST BE SECURED WITH HOOD PINS.

11-STOCK B PILLARS MAY BE REMOVED FROM THE CAR.

12-FRONT AND REAR BUMPERS MUST BE INSTALLED SECURELY AND REMAIN STOCK WITH NO SHARP OR PROTRUDING EDGES.

13-STOCK OR AFTERMARKET BUMPER COVER ARE BOTH ALLOWED.

14-ROUND, STEEL AFTERMARKET BUMPERS ARE ALLOWED TO BE RUNBUT MUST TURN BACK TOWARDSFRAME INSIDE THE FENDER. 1.750 MAX DIAMETER AND 0.095 MINIMUM THICKNESS.

15-ANY HOLES IN FRONT AND REAR FIREWALLS MUST BE FULLY SEALED AND SECURE WITH 0.063 MAX THICKNESS ALUMINUM OR STEEL.

16-INTERIOR DECKING OF ANY KIND IS NOT ALLOWED.

​

FRAME

1-ROLL CAGE MUST BE 4 POINT MINIMUM CAGE CONSTRUTED OF 0.095 MINIMUM STEEL TUBING.

2-WELDS AND WORKMANSHIP WILL BE INSPECTED BY WARTBURG OFFICAL FOR STRUCTURAL INTERITY AND MUST PASS VISUAL INSPECTION.

3-THE ROLL CAGE MUST BE FULLY CONTAINED WITHIN THE DRIVER COMPARTMENT. NO PART OF THE CAGE MAY PROTUDE OUTSIDE OF THE DRIVER/PASSENGER COMPARTMENTS.

4-CAGE MUST BE WELDED TO THE FRAME AND CAN NOT BE SET BACK ANY FURTHER THAN THE FRONT EDGE OF THE REAR FLOORBOARD.

5-FRONT DOOR MUST HAVE STEEL 0.095 MINIMUM THICKNESS STEEL BARS MOUNTED SECURELY.

6-DRIVER DOOR MUST HAVE A MINIMUM OF 4 DOOR BARS WITH STEEL PLATE RECOMMENED.

7-PASSENGER DOOR MUST HAVE A MINIMUM OF 3 DOOR BARS.

8-DOWN BARS FRON AND REAR ARE NOT PERMITTED.

9-A MAXIMUM OF 2 BARS WITH HOOPS ARE PERMITTED TO BE INSTALLED TO PROTECT RADIATOR.

​

ENGINE

1-ENGINES MUST BE COMPLETY STOCK 4.6L SOHC 2V THAT MATCH MAKE AND MODEL OF CAR ITS INSTALLED IN.

2-ABSOLUTELY NO TUNING ALLOWED TO THE ENGINE THROUGH ANY MEANS.

3-AC CONDENCERS MUST BE REMOVED AND INSTALLED.

4-INTAKE MANIFOLDS MUST REMAIN STOCK OR DOORMAN REPLACEMENT.

5-ONLY STOCK IGNITION AND COILS WILL BE ALLOWEDE. NO AFTERMARKET OR PERFORMANCECOILS WILL BE ALLOWED.

6-ALL TRACTION CONTROL DEVICES WHEATHER ELECTRONICALLY CONTROLED IN THE IGNITION SYSTEMS, WHEEL SENSORS, BRAKES, OR ANY MEANS OF MEASURING GROUND SPEED TO CONTROL WHEEL SPIN, ARE STRICTLY PROHIBITED.

7-NO COMPUTER CONTROLLED DEVICES, GPS, CELLULAR, SATELITE OR WIFI DEVISE OR ANY OTHER TYPE ODF ELECTRONIC TRACKING OR LOCATING DEVISES OF ANY KIND ARE ALLOWED ANYWHERE ON OR ATTACHED TO THE CAR.

8-CATALYIC CONVERTERS MAY BE REMOVED

9-EXHAUST MUST BE SECURELY MOUNTED AND RUN PAST DRIVERS COMPARTMENT AND EXIT ON EOTHER SIDE OR UNDER THE HOOD.

10-EXHAUST MUFFLERS ARE REQUIRED TO BE INSTALLED.

11-EXHAUST MANIFOLDS MUST REMAIN STOCK.

12-TRANSMISSION MUST BE COMPLETLY STOCK TRANSMISSION FORM THE YEAR AND MAKE, MODEL THATS ITS INSTALLED IN.

13-REMOVING GEARS OR LIGHTNING GEARS ARE STRICKLY PROHIBITED.

14-ALL GEARS MUST BE OPERATIONAL AT ALL TIMES.

15-TRUCK OR 5.4 TRANSMISSIONS ARE NOT ALLOWED.

16-ONLY STOCK TORQUE CONVERTERS FOR THE YERAR, MAKE AND MODEL THAT ITS INSTALLED IN.

17-STOCK DRIVESHAFTS ONLY. MUST BE PAINTED WHITE.

18-A DRIVESHAFT HOOP MUST BE SECURELY MOUNTED 6 INCHES REARWARD FROM FRONT U JOINT

19-REAREND GEAR- ONLY A 2.73, 3.27, 3.55, 3.73 GEAR RATIO SET ARE ALLOWED TO BE INSTALLED.

20.ALL GEAR SETS MUST REMAIN COMPLETLY STOCK WITH NO AFTERMARKET PARTS OR LIGHTNING FOR WEIGHT OR PERFORMANCE.

21-GEAR SETS MAY BE WELDED OR UTLIZE AFTERMARKET POSI- LOCKER SETUP.

22-BRAKE- ALL BRAKE COMPONENTS INCLUDING ROTORS AND CALIPERS MUST REMAIN STOCK FOR YEAR AND MAKE OF MODEL. NO SLOTTED OR DRILLED ROTORS OR LIGHTWEIGHT CALIPERS ALLOWED.

23-ALL 4 BRAKES MUST BE OPERATIONAL AT ALL TIMES.

24-FUEL- ONLY STOCK PUMP GAS IS ALLOWED WITH A MAXIMUM OF 93 OCTANE.

25-NO E85 OR RACE FUEL ALLOWED.

26-THE STOCK FUEL TANK AND PUMP MUST NE USED AND REMAIN IN STOCK POSITION.

​

SUSPENSION

1-ALL SUSPENSION MUST REMAIN STOCK WITH ZERO ALTERATIONS OR AFTERMARKETPARTS.

2-ONLY STOCK FRONT AND REAR SPRINGS MAY BE USED. NO ALTERING SPRINGS IN ANY WAY. SPRING MUST REMAIN THE SAME SIZE, DIAMETER AND HEIGHT ON ALL 4 CORNERS.

3-STRUT AND SPRING ASSEMBLIES MUST REMAIN STOCK AND MATCH SIDE TO SIDE.

4-IF USED, FRONT OR REAR SWAY BAR MUST BE STOCK AND MOUNTED IN STOCK LOCATION. 

5-EACH SUSPENTION COMPONENT, INCLUDINGHEATING OR BEANDING IS NOT ALLOWED.

6-IT IS ALLOWED TO RUN LOWER FRONT CAMBER BOLT FROM MOOG OR EQUIVALENT3 DEGREES MAX.

7-ONLY STOCK REPLACEMENTS SHOCKD WILL BE ALLOWED. NO RACING STLYE SHOCK ALLOWED.

8-ONLY STOCK TRAILING ARMSWILL BE ALLOWED.

9-TRALING ARM BUSHINGS MUST BE STOCK OR STOCK REPLACEMENT AND NOT AND NOT BE WORN TO ALLOW ADDITIONAL MOVEMENT ON TRACK. 

10-TRAILING ARM BUSHINGS MUST BE STOCK OR STOCK REPLACEMENT. NO POLYURETHANE BUSHINGS ALLOWED.

​

WHEELS/TIRES

1-WHEELS MUST BE STOCK STEEL WHEEL. NO RACE WHEEL ALLOWED.

2-ALL 4 WHEELS MUST BE THE SAME SIZE AND OFFSET.

3-NO WHEEL SPACER OR ANY OTHER MEANS TO SPACE OUT THE WHEEL ARE NOT ALLOWED AT ANY TIME.

4-NO OFFSET WHEELS ALLOWED ON CARS 2003 AND NEWER.

5-CARS 2002 AND OLDER MAY RUN STOCK STEEL DODGE CHARGER17 INCH WHEELS.

6-MODIFIACTIONS TO STOCK WHEELS ARE NOT ALLOWED.

7-ALL 4 TIRES INSTALLED ON THE VEHICLE MUST BE DOT APPROVED FOR MAD USE AND MUST BE SAME WIDTH, ASPECT RATIO, CONSTRUCTION AND RIM DIAMETER.

8-SNOW AND ALL TERRAIN TIRES ARE NOT ALLOWED.

9-DIRECTION OR HIGH-PERFORMANCE TIRES ARE NOT ALLOWED.

10-NO ACING TIRES ALLOWED.

11-ALL 4 TIRES MUST BE UNDER 350 TREAD WEAR.

12-AIR BLEEDER VALVES OF ANY KIND ARE NOT ALLOWED.

13-GROOVING, SIPING, AND DRILLING TIRES ARE NOT PERMITTED.

14-CHEMICAL ALTERATIONS, VULCANIZING, TIRE SOFTENING, DEFSCING AND/OR ALTERING THE FACE OF THE TIRE LETTERING AND/OR STAMPING IS NOT ALLOWED.

​

-ONLY THE FORD CROWN VICTORIA, MERCURY GRAN MARQUIS OR LINCOLD TOWN CAR WILL BE ALLOWED. EACH MAKE MUST BE 1991 OR NEWER.

-THE ENTIRE OUTER BODY AND CORRESPONDING COMPONENTS MUST MATCH THE YEAR, MODEL AND MAKE OF THE CAR. 

-SWAPPING BODIES ON DIFFERENT FRAMES OR VICEVERSA IS STRICTLY PROHIBITED.

-THE ENTIRE FRAME ASSEMBLY MUST BE COMPLETE AS FROM FACTORY.

-ANY MODIFAIATION ON ANY PART OF THE CAR TP ADD OR REMOVE WEIGHT IS NOT ALLOWED.

-ADDING WEIGHT OR BALLAST TO THE CAR IS NOT ALLOWED.

​

​

​

​

​

​​